Friedrich SV12 Manual de usuario

Room Air ConditionerService and PartsManualSlider CasementSV08 / SV10 / SV12 (01/05)115Volts • SV08A10A • SV10A10A • SV12A10AHighCoolMedFa

—10—— Replacement of the refrigerant.1. When replacing the refrigerant, be sure toDischarge the refrigerant system using a FreonTMrecovery System.If t

—11—Equipment needed: Vacuum pump, Charging cylinder, Manifold gauge, Brazing equipment. Pinch-off toolcapable of making a vapor-proof seal, Leak det

—12—3. INSTALLATION3.1 HOW TO INSTALL THE UNIT1. To avoid vibration and noise, make sure the unit isinstalled securely and firmly.2. Install the unit

—13—3.4 WINDOW REQUIREMENTS1. These instructions are for a horizontal sliding or acasement window.2. The electrical outlet must be within reach of the

—14—1. Loosely attach the support bracket to the bottom ofbracket using bolts, washers, and nuts. Attach theleveling bolt and nut. (See Figure 22)2. R

—15—8. Slide curtain into curtain frame. Slide curtain frameassembly into side guides of the air conditionercabinet. Make sure curtain is firmly enclo

—16—4. TROUBLESHOOTING GUIDE4.1 OUTSIDE DIMENSIONS 368(14 1/2)521(20 1/2)607(23 3/5)CAPILLARY TUBECOMPRESSORTURBO FANEVAPORATOR COILCONDENSER COILF

—17—4.3 TROUBLESHOOTING GUIDEIn general, possible trouble is classified in two kinds.The one is called Starting Failure which is caused from an electr

—18—Fails to StartCheck circuit breakerand fuse.Gas leakage of feeler bulbof thermostatCheck control switch.Fan only fails to start.Improper wiring.De

—19—COMPLAINT CAUSE REMEDYCheck voltage at outlet. Correct if none.Check voltage to rotary switch. If none, check powersupply cord. Replace cord if ci

—2—1. PREFACE1.1 SAFETY PRECAUTIONS...21.2 INSULATION RESISTANCE TEST...21.3 SPECIFICATIONS...

—20—COMPLAINT CAUSE REMEDYCheck the position of knob If not at the coldestsetting, advance the knob to this setting and restartunit.Check continuity o

5. SCHEMATIC DIAGRAM5.1 CIRCUIT DIAGRAM MODEL : SV10A10A / SV1210A—21—SV10A10A SV12A10APART NO.1 POWER CORD - - 1 S2 ROTARY SWITCH 67300501 1 S3 FAN

—22—5.2 CIRCUIT DIAGRAM MODEL : SV08A10ASV08A10APART NO.1 POWER CORD 67300005 1 S2 ROTARY SWITCH 67300501 1 S3 FAN MOTOR 67303014 1 S4 CAPACITOR 6730

6. EXPLODED VIEW—23—554030148000352390-2349001349600346811354210152312147581145200147582-2135312147582-1135301264110269310 266003249950130910359011130

—24—7. REPLACEMENT PARTS LIST MODEL : SV08A10A, SV10A10A, SV12A10AP/NoSV08A10A SV10A10A SV12A10A130410 BASE ASSEMBLY, SINGLE 67302911 67302910 R13091

—25—MEMO

—26—MEMO

Printed in the U.S.APost Office Box 1540 • 4200 N. Pan Am Expressway • San Antonio, Texas 78295-1540 • (210) 357-4400 • FAX (210) 357-4480FRIEDRICH AI

—3—POWER SUPPLYCOOLING CAPACITY (Btu/h)INPUT (W)RUNNING CURRENT (A)E.E.R (BTU/W.h)INDOOR (°C)OUTDOOR (°C)REFRIGERANT (R-22) CHARGEEVAPORATORCONDENSERF

—4—1.4 FEATURES• Designed for COOLING ONLY.• Powerful and whispering cooling.• Simple installation and service.• Low air-intake, top cooled-air discha

—5—2.1 MECHANICAL PARTS2.1.1 FRONT GRILLE1. Open the inlet grille downward and remove the airfilter.2. Remove the screws which fasten the frontgrille.

—6—2.2 AIR HANDLING PARTS2.2.1 AIR GUIDE AND TURBO FAN1. Remove the front grille. (Refer to section 2.1.1)2. Remove the cabinet. (Refer to section 2.1

—7—2.2.3 SHROUD1. Remove the fan. (Refer to section 2.2.2)2. Remove the shroud. (See Figure 8)3. Re-install the components by referring to theremoval

—8—2.3.3 CAPACITOR1. Remove the cabinet. (Refer to section 2.1.2)2. Remove the screw and the clamp which fasten thecapacitor.3. Disconnect all the lea

—9—2.3.7 MOTOR1. Remove the cabinet. (Refer to section 2.1.2)2. Remove the turbo fan. (Refer to section 2.2.1)3. Remove the fan. (Refer to section 2.2